Answer:
10.57% of N in acetanilide
Explanation:
All nitrogen in the sample is converted in NH₃ in the Kjeldahl determination. The NH₃ reacts with H₂SO₄ as follows:
2NH₃ + H₂SO₄ → 2NH₄⁺ + SO₄²⁻
The acid in excess in titrated with Na₂CO₃ as follows:
Na₂CO₃ + H₂SO₄ → Na₂SO₄ + H₂O + CO₂
To solve this question we must find the moles of sodium carbonate = Moles of H₂SO₄ in excess. The added moles - Moles in excess = Moles of sulfuric acid that reacts:
Moles Na₂CO₃ anf Moles H₂SO₄ in excess:
0.025L * (0.05mol / L) = 1.25x10⁻³ moles Na₂CO₃ / 0.01360L =
0.09191M * 0.250L = 0.0230 moles H₂SO₄ in excess.
Moles H₂SO₄ added:
0.050L * (0.50mol / L) = 0.0250 moles H₂SO₄ added
Moles that react:
0.0250 moles - 0.0230 moles = 0.0020 moles H₂SO₄
Moles of NH₃ = Moles N:
0.0020 moles H₂SO₄ * (2mol NH₃ / 1mol H₂SO₄) = 0.0040 moles NH₃ = Moles N
mass N and mass percent:
0.0040 moles N * (14g / mol) = 0.056gN / 0.53g * 100 =
10.57% of N in acetanilideWhich element would you expect to have the highest electronegativity?
Answer:
Fluorine
Explanation:
It's tendency to gain electron is higher than Ca and P
what do you call a solid which dissolves?
Answer:
solute
Explanation:
for example sugar salt etc
solute dissolve in solvent
What are the chemical reactions involved in CO2 emission?
What is a type of radiation produced when the unstable nucleus of a radioactive element emits a helium nucleus?
A. deuterium radiation
B. beta radiation
C. alpha radiation
D. gamma radiation
EASYYYYYY1
Compare and contrast a sanitary landfill and a secure landfill.
Answer:
Secure landfills Landfilling of hazardous solid or containerized waste is regulated more stringently than landfilling of municipal solid waste. Hazardous wastes must be deposited in so-called secure landfills, which provide at least 3 metres (10 feet) of separation between the bottom of the landfill and the underlying bedrock or groundwater table.
Explanation:
Which type of stoichiometry problems does not require the use of molar mass?
Answer:
Explanation:
It is volume-volume problems that does not require the use of molar mass.
What is a dominant trait and a recessive trait
Answer:
Dominant traits are always expressed when the connected allele is dominant, even if only one copy exists. Recessive traits are expressed only if both the connected alleles are recessive.
Explanation:
Freckles, cleft chin and dimples are all examples of a dominant trait.
Helllpppppppppppppppppppp
Answer:
90% of people marry there 7th grade love. since u have read this, u will be told good news tonight. if u don't pass this on eight comments your worst week starts now this isn't fake. apparently if u copy and paste this on ten comments in the next ten minutes you will have the best day of your life tomorrow. you will either get kissed or asked out in the next 53 minutes someone will say i love you.!
Explanation:
Nitrogen-fixers are the critical links between ______.
A. atmospheric nitrogen and organisms that need nitrogen to survive
B. atmospheric nitrogen and the formation of new soil
C. atmospheric nitrogen and the formation of new atmospheric nitrogen
D. None of the above
Please answer correctly and explain
Nitrogen-fixers are the critical links between atmospheric nitrogen and organisms that need nitrogen to survive.
Where Nitrogen fixers are used?Nitrogen fixers are the compounds which are used in the nitrogen fixation process to convert the nitrogen molecule in other nitrogenous compounds.
So, the nitrogen fixers converts the atmospheric nitrogen molecule (N₂) into the other compounds like ammonia (NH₃) or any other useful nitrogenous compounds which will be used or absorbed by the soil or any other aquatic species. Some examples of nitrogen fixers are bacteria, clostridium, rhizobium, and many more.
Hence option (A) is correct i.e. atmospheric nitrogen and organisms that need nitrogen to survive.
To know more about nitrogen fixers, visit the below link:
https://brainly.com/question/21040043
A student performs an experiment with three unknown fluids and obtains the following measurements: Fluid A: m = 2060 g, V = 2000 mL Fluid B: m = 672 g, V = 850 mL
Fluid C: m = 990 g,
V = 1100 mL
Answer:
fluid - A is 1.03
fluid -B is 0.790
fluid - C is 0.90
Explanation:
In our exprimetal fluid, the density of
fluid - A is 1.03
fluid -B is 0.790
fluid - C is 0.90
The fluid with high density settles at bottom of the beaker and least dense fluid forms layer on the surface .
Fluid A is 1.03
Fluid B is 0.790
Fluid C is 0.90
What is measurment?Measurment is a process by which we can measure any physical quantity with the help of different apparatus. For example if one can want to measure the distance than he can use the a simple measuring scale.
Distance can be measured in kilometer,meter, centimeter etc. Temperature can be measured with the help of glass tube thermometer as glass tube is a simple temperature measuring appratus and glass tube thermometer is used to measure temperature in fahrenheit (F).
Measurment is a general process which can be used by a common person in his daily life. Every common thing which we use in our routine life need to be measured like if we buy sugar it will be measured in kilogram or gram. If a person buy milk it can measured in liter.
Therefore,Fluid A is 1.03
Fluid B is 0.790
Fluid C is 0.90
Learn more about measurment here:
https://brainly.com/question/4725561
#SPJ2
Para solucionar el ejercicio primero se debe conocer el número atómico de los elementos para determinar cuantos electrones tiene cada uno N: número atómico 7, tiene 7 electrones Nivel 1: 2 electrones Nivel 2: 5 electrones P: número atómico 15, tiene 15 electrones Nivel 1: 2 electrones Nivel 2: 8 electrones Nivel 3: 5 electrones Cl: número atómico 17, tiene 17 electrones
Answer:
El número atómico se refiere al número de protones o electrones de un átomo.
Explicación:
El número atómico se refiere a la cantidad de protones o la cantidad de electrones que giran alrededor de las capas u órbita de un átomo, por lo que el número atómico 7 representa que el átomo tiene 7 electrones o protones mientras que, por otro lado, el número atómico 17 muestra el número de electrones o protón. Solo hay dos electrones que entran en la primera órbita y en el resto de las capas tiene espacio para 8 electrones por lo que los átomos pierden o agregan electrones en su capa más externa para obtener estabilidad.
A 12.0 L balloon at 84 °C is cooled until it
becomes 5.0 L. To what temperature was
the balloon cooled?
The ideal gas relates the volume, pressure, and temperature to each other. The balloon was cooled to -120 degrees celsius.
What is Charle's law?Charle's law states the direct relationship between the volume and the temperature of the hypothetical gas. The law is given as,
[tex]\rm \dfrac{V_{1}}{T_{1}} = \rm \dfrac{V_{2}}{T_{2}}[/tex]
As it can be seen from the question the volume of the gas in the balloon is decreasing so the temperature will also decrease.
Given,
Initial volume = 12.0 L
Final volume = 5.0 L
Initial temperature = 357.15 K
The final temperature is calculated as:
[tex]\begin{aligned} \rm T_{2} &= \rm \dfrac{V_{2}T_{1}}{V_{1}}\\\\&= \dfrac{5\times 357.15}{12}\\\\&= 148.81\;\rm K\end{aligned}[/tex]
Therefore, -120 degrees celsius is the final temperature of the balloon.
Learn more about Charle's law here:
https://brainly.com/question/16404056
#SPJ2
At a hydroelectric power plant, potential energy is changed into kinetic energy. The kinetic energy is then transformed into electrical energy. i What is the source of the energy that turns the turbine in the power plant? Chemical energy of water molecules as they fall Gravitational potential energy of water behind the dam Elastic potential energy of the water molecules as they bounce over the dam Electrical energy from power lines that connect the hydroelectric plant to a grid
Answer:
Gravitational potential energy of water behind the dam
Explanation:
Energy can be defined as the ability (capacity) to do work. The two (2) main types of energy are;
a. Gravitational potential energy (GPE): it is an energy possessed by an object or body due to its position above the earth.
b. Kinetic energy (KE): it is an energy possessed by an object or body due to its motion.
Hydroelectric power plant refers to a renewable source of energy used for the generation of electricity, through the use of powerful hydraulic steam turbines operating at high voltage and are being driven by the energy acquired by water falling from a height and flowing through a penstock (pipe) i.e the mechanical energy (gravitational potential energy + kinetic energy).
At a hydroelectric power plant, potential energy is changed into kinetic energy. The kinetic energy is then transformed into electrical energy.
The source of the energy that turns the turbine in the power plant is Gravitational potential energy of water behind the dam, usually from streams or rivers.
NH₄⁺(aq)+NO₃⁻(aq) → NH₄NO₃(s)
How much energy is released when 3 moles of NH₄+ react?
1) -25.69 kJ
2) -51.38 kJ
3) -77.07 kJ
4) -102.76 kJ
Please help me classify properly.
Answer:C
Explanation:
Homogeneous Mixture
Answer:
homogeneous mixture
Explanation:
it is the same throughout so therefore it can be separated
transmutation occurs during which type of radioactive decay
Explanation:
Transmutation, conversion of one chemical element into another. A transmutation entails a change in the structure of atomic nuclei and hence may be induced by a nuclear reaction (q.v.), such as neutron capture, or occur spontaneously by radioactive decay, such as alpha decay and beta decay (qq. v.).
Oxygen is the 16th element on the periodic table and the number of neutrons is 8. Using the formula A=Z+N, determine by calculation the atomic number for oxygen *
a. 6
b. 8
c. 24
d. 16
Answer:
the answer is twenty-four
Tropical, temperate, and taiga refer to what type of biomes?
A. grasslands
B. deserts
C. the tundra
D. forests
Answer:
From my view the answer is
D. Forests
A student drops a white tablet into a glass of water, producing
carbon dioxide gas. This is a demonstration of
A. a change of state.
B. a chemical reaction.
C. the creation of matter.
O D. the movement of electricity.
Answer:
A chemical reaction
Explanation:
i need help i have a homework assignment to finish and this is the last question help please and thank u
Please help!!
The diagram shows the electron configuration of an atom of an element for the electrons in the s and p orbitals.
What is the group number of the element in the periodic table?
A) 1
B) 2
C) 13
D) 15
Answer:
15
Explanation:
because since the outer shell has 5 electron then add 5 and 10 to get 15
Step 6: Measure Solubility in Boiling Water
110
100
80
100 ml
60
90
40
20
Temperature of the water to the nearest degree:
°C. DONE
Intro
Answer:
the answer is 102- i took did it on edg
Explanation:
The ability of a material, the solute, to combine with some other substance, the solvent, is known as solubility. Temperature of the water to the nearest degree is 110 °C for the given solubility.
The ability of a material, the solute, to combine with some other substance, the solvent, is known as solubility in chemistry. Insolubility, or the solute's inability to create such a solution, is the opposite property.
The concentration of a solute inside a saturated solution—a solution where no more solute could be dissolved—is typically used to gauge the degree of a substance's solubility in a particular solvent. Temperature of the water to the nearest degree is 110 °C for the given solubility.
To know more about solubility, here:
https://brainly.com/question/14366471
#SPJ7
is copper an elementary substance or a compound?
In a transverse wave, this is the magnitude of height of a wave from origin to crest.
In a longitudinal wave, this is corresponds to how much the wave is compressed, as compared to areas of little compression.
a transverse wave, this is the magnitude of height of a wave from origin to crest. In a longitudinal wave, this is corresponds to how much the wave is compressed, as compared to areas of little compression. This is wave whose energy travels in the same direction as the energy is transferred
In a transverse wave, amplitude is the magnitude of height of a wave from origin to crest. In a longitudinal wave, crest is corresponds to how much the wave is compressed
What are waves?A wave is a dynamic disturbance of one or more quantities that propagates and is commonly described by a wave equation.
In transverse wave, magnitude of height of a wave from origin to crest part is called amplitude.In longitudinal wave, the part of the wave in which compression is occur will known as crest.Hence for the transverse wave that is amplitude and for the longitudinal wave that is crest.
To know more about transverse & longitudinal waves, visit the below link:
https://brainly.com/question/13761336
#SPJ2
A solute can be obtained from a solution by...
Answer:
Evaporating the solvent
Explanation:
An element A has an atomic number of 11 and another element B has an atomic number 17 (A
and B are not actual chemical symbols of elements)
i. What group on the periodic table does A belong?
ii. What type of bond will be formed between A and B? Explain.
(2mks
(1ml
iii.
Write the formula of the compound that will be formed between A and B.
(lm
b. Arrange the species X, X5+ and X. in order of increasing size.
Answer:
can anyone tell me how to get +7!67:$'!$
The thermal energy of matter increases when ___.
A. Heat flows of the matter
B. The mass of the matter decreases
C. Heat flows into the matter
D. The temperature decreases
A solution's hydrogen ion concentration is 1 x 10-SM.
What is the pH?
Answer:
the Ph is
Explanation:
90rn hub
What is represented by this notation?
Na loses one proton to Cl.
Na loses one electron to Cl.
Na gains two protons from Cl.
Na gains one electron from Cl.
Answer:
it's the third
Explanation:
I need to fill 20 spaces. don't mind that
Answer:
Na gains two protons from Cl.
Explanation:
this should help
Which set of elements represents a period within the Periodic Table?
H, He, Ar , Xe , Rn ,
N, P, As, Sb , Bi
K, V, Fe, Ga , Kr
La, Pa, Sm, Tb, Yb