Answer:
6544.07 J
Explanation:
From the question given above, the following data were obtained:
Distance (d) = 15 m
Force (F) = 628 N
Angle (θ) = 46°
Workdone (Wd) =?
The work done can be obtained by using the following formula:
Wd = Fd × Cos θ
Wd = 628 × 15 × Cos 46
Wd = 9420 × 0.6947
Wd = 6544.07 J
Therefore, the workdone is 6544.07 J
it requires 350 joules to raise a certain amount of a substance from 10.0°c to 30.0°c. the specific heat of the substance is 1.2 j/g° is the mass of the substance?
a.12 g
b.15 g
c.18 g
d.30 g
The mass of the substance is 15 g,determined using the specific heat and heat energy values.
What is the mass of the substance?The specific heat capacity (c) of a substance is the amount of heat energy required to raise the temperature of 1 gram of that substance by 1 degree Celsius. In this case, the specific heat of the substance is given as 1.2 J/g°C.
To find the mass of the substance, we can use the formula:
Heat energy (Q) = mass (m) × specific heat (c) × change in temperature (ΔT)
Given that the heat energy required is 350 J, the specific heat is 1.2 J/g°C, and the change in temperature is (30.0°C - 10.0°C) = 20.0°C, we can rearrange the formula to solve for the mass:
350 J = m × 1.2 J/g°C × 20.0°C
Dividing both sides of the equation by (1.2 J/g°C × 20.0°C), we find:
m = 350 J / (1.2 J/g°C × 20.0°C) = 14.58 g
Rounding to the nearest whole number, the mass of the substance is approximately 15 g.
Learn more about Mass
brainly.com/question/11954533
#SPJ11
A box experiences a varying net force that changes its velocity. The graph shows the velocity of the box as a function of time. Which of the following correctly describes the net work, Wet, done on the box for the given intervals of time? (A) Between 0 and 4 Between 1 and 12 Between 12 and 13 Wnet > 0 Whet = 0 Wher 0 Whee> 0 © Between 0 and Between 1 and 12 Between 12 and 13 Wher = 0 Wher = 0 Wace 0 Weet > 0 Wher > 0
A box experiences a varying net force that changes its velocity. Based on the description provided, it seems that the options (A) and (C) are the most relevant to the question.
Between 0 and 4:
The velocity of the box is increasing, which indicates that there is a positive acceleration.
Since the net force is causing an acceleration in the direction of motion, the net work done on the box is positive.
Therefore, the correct statement would be: Wnet > 0.
Between 1 and 12:
The velocity of the box is constant, which means there is no acceleration.
In this case, the net force acting on the box is zero.
When the net force is zero, no net work is done on the box.
Therefore, the correct statement would be: Wnet = 0.
Between 12 and 13:
The velocity of the box is decreasing, indicating a negative acceleration.
Since the net force is acting opposite to the direction of motion, the net work done on the box is negative.
Therefore, the correct statement would be: Wnet < 0.
Based on this analysis, the correct description would be:
Between 0 and 4: Wnet > 0
Between 1 and 12: Wnet = 0
Between 12 and 13: Wnet < 0
Learn more about Velocity from the link given below.
https://brainly.com/question/30559316
#SPJ4
A little girl is going on the merry-go-round for the first time, and wants her 57kg mother to stand next to her on the ride, 2.8m from the merry-go-round's center.
If her mother's speed is 4.6m/s when the ride is in motion, what is her angular momentum around the center of the merry-go-round?
Could you please show your work? I don't understand how to work this problem at all.
The angular momentum of the mother around the center of the carousel is 263.84 kg·m²/s.
Angular momentum is a measure of rotation and is defined as the product of the moment of inertia and angular velocity. In this case, we need to calculate the angular momentum of the mother around the center of the carousel.
The angular momentum formula is:
L = Iω
where L is angular momentum, I is the moment of inertia and ω is angular velocity.
To calculate the moment of inertia, we need to know the mass of the object and its distance from the axis of rotation. The moment of inertia of a point of mass rotated along a distance r about an axis is given by:
I = mr²
where m is the mass and r is the distance from the axis of rotation.
In this case, the mass of the mother is 57 kg and the distance from the center of the carousel is 2.8 m. Therefore, the mother's moment of inertia is:
I = (57 kg) × (2.
8 m)² = 439.04 kg m²
The given angular velocity of 4.6 m/s.
Now L = Iω:
L = (439.04 kg m²) × (4.
6 m/s) = 2018.144 kg·m²/s ≈ 2018.14 kg·m²/s
Therefore, the angular momentum of the mother around the center of the carousel is approximately 2018.14 kg ·m²/s.
The angular momentum of the mom around the center of the carousel is 263.84 kg·m²/s.
To learn more about momentum, visit
https://brainly.com/question/29512279
#SPJ11
a uniform magnetic field of 4.95 t points in some direction. consider the magnetic flux through a large triangular wire loop that has three equal sides of 1.55 m.
The absolute value of the magnetic flux at its maximum is ∅[tex]_{max[/tex] = 12.101 Weber.
We learn from the question that
The magnetic field is defined as B = 7.35 T
One of the triangle's sides is d = 19.5 m
In general, the absolute value of magnetic flux is represented mathematically as
∅ = B × [tex]A_{COS}[/tex] (Ф₁)
At its most extreme, Ф₁ = 0
So
The magnetic flux's absolute value at its maximum.
∅[tex]_{max}[/tex] = B × A
Now that we know the triangle has equal sides, the angle each produces with the other Ф = 60° is because the total angle in a triangle is 180.
The height of the triangular loop is now calculated mathematically using SOHCAHTOA as
sin Ф = [tex]\frac{h}{d}[/tex]
=> sin (60) = [tex]\frac{h}{1.95}[/tex]
=> h = sin(60) × 1.95
=> h = 1.6887 m
As a result, the area is rated as
A = [tex]\frac{1}{2}[/tex] × d × h
value substitution
A = 0.5 × 1.95 × 1.6887
A = 1.6465 m²
Thus
∅[tex]_{max}[/tex] = 7.35 × 1.6465
∅[tex]_{max}[/tex] = 12.101 Weber
To know more about magnetic flux:
https://brainly.com/question/31501008
#SPJ4
Correct question:
A uniform magnetic field of 7.35 T points in some direction. Consider the magnetic flux through a large triangular wire loop that has three equal sides of 1.95 m. Determine the maximum of the absolute value of the magnetic flux.
A house painter uses the chair and pulley arrangement of the figure to lift himself up the side of a house. The painter's mass is 68kg and the chair's mass is 8.0kg .
With what force must he pull down on the rope in order to accelerate upward at 0.20m/s2 ?
The house painter must pull down on the rope with a force of 15.2 N to accelerate upward at 0.20 m/s².
Mass of the painter, m = 68 kg
Mass of the chair, M = 8.0 kg
Acceleration, a = 0.20 m/s²
The tension in a rope in such an arrangement is,
T = (m + M) x a
Substituting the given values ,
T = (m + M) x a
T = (68 kg + 8.0 kg) x 0.20 m/s²
= 15.2 N
Therefore, the house painter must pull down on the rope with a force of 15.2 N to accelerate upward at 0.20 m/s².
Learn more about the force:
brainly.com/question/27777011
#SPJ11
a convex lens always produces a virtual image. true or false? true false
The statement "a convex lens always produces a virtual image" is not true.
A convex lens produces both real and virtual images, depending on the position of the object in relation to the focal point of the lens.
A convex lens is a converging lens, meaning it focuses parallel rays of light to a point called the focal point. Convex lenses have a thicker middle and thinner edges. The distance from the center of the lens to the focal point is called the focal length.
A virtual image is one that appears to be on the opposite side of the lens from the object. The image is not real; it cannot be projected onto a screen or viewed directly.
Virtual images can only be seen when looking through a lens.
A real image is formed when light rays pass through a lens and converge to form an image that can be projected onto a screen.
Real images are inverted and can be seen without a lens because they are formed by actual light rays converging at a point.
Learn more about the convex lens:brainly.com/question/29282959
#SPJ11
An electron is acted upon by a force of 5.50×10−15N due to an electric field. Find the acceleration this force produces in each case:
The electron's speed is 4.00 km/s . ---ANSWER---: a=6.04*10^15 m/s^2
The acceleration produced by the force of 5.50 × 10⁻¹⁵ N on an electron with a speed of 4.00 km/s is 6.04 × 10¹⁵ m/s².
What is an acceleration?Acceleration is a fundamental concept in physics that refers to the rate of change of velocity. It is a vector quantity, meaning it has both magnitude and direction.
The electron's speed is 4.00 km/s.
The acceleration produced by the force is given by the equation:
a = F / m
where a is the acceleration, F is the force, and m is the mass of the electron.
Given:
Force, F = 5.50 × 10⁻¹⁵ N
Speed, v = 4.00 km/s
To find the acceleration, we need to determine the mass of the electron. The mass of an electron is approximately 9.109 × 10⁻³¹ kg.
Substituting the values into the equation, we have:
a = (5.50 × 10⁻¹⁵ N) / (9.109 × 10⁻³¹ kg)
Simplifying, we get:
a = 6.04 × 10¹⁵ m/s²
Therefore, the acceleration produced by the force of 5.50 × 10⁻¹⁵ N on an electron is 6.04 × 10¹⁵ m/s².
To learn more about acceleration,
https://brainly.com/question/25876659
#SPJ4
In middle and late childhood, it is recommended that children have at least of moderate exercise, and of vigorous exercise. a. 15 minutes: 45 minutes b. 45 minutes: 15 minutes c. 60 minutes: 10 minutes d. 30 minutes; 30 minutes e. 10 minutes; 60 minutes
In middle and late childhood, it is recommended that children have at least c. 60 minutes of moderate exercise, and 10 minutes of vigorous exercise.
The amount of physical activity required by children varies according on their age. Children aged 3 to 5 years must be physically active throughout the day. Children and adolescents aged 6 to 17 must be physically active for 60 minutes every day.
This may appear to be a lot, so don't worry! Children may already be meeting the required levels of physical activity. You can also explore how to encourage children to participate in age-appropriate, pleasurable, and varied activities.
The majority of their daily 60 minutes should be spent walking, running, or doing anything that causes their hearts to race. At least three days per week should be spent engaging in high-intensity activities.
To know more about physical activity:
https://brainly.com/question/14338730
#SPJ4
In the measurement of the voltage as a function of time, thevoltage is measured at fixed time intervals.
(a) true
(b) false
In the measurement of the voltage as a function of time, the voltage is measured at fixed time intervals, this statement is true. Therefore, option A is correct.
In the measurement of voltage as a function of time, it is common to measure the voltage at fixed time intervals. This approach allows for the creation of a time-domain representation of the voltage signal.
By taking voltage measurements at regular intervals, one can capture the variations in voltage over time and plot it as a waveform or time series. This method is widely used in various fields, including electrical engineering, physics, and signal processing.
To learn more about the voltage, follow the link:
https://brainly.com/question/32002804
#SPJ4
an artificial satellite circles the earth in a circular orbit at a location where the acceleration due to gravity is 7.72 m/s2. determine the orbital period of the satellite.
The orbital period of the artificial satellite that circles the earth in a circular orbit is 1 hour and 34 minutes.
The given value of 7.72 m/s² seems unusually high for an orbiting satellite around the Earth.
Assuming the acceleration due to gravity (g) is 9.81 m/s², which is the approximate average value at the Earth's surface, we can proceed with the calculations.
Using the equation [tex]$g = \frac{{GM}}{{r^2}}$[/tex], we can solve for the average distance (r) from the center of the Earth to the satellite:
[tex]$r^2 = \frac{{GM}}{{g}}$[/tex]
Plugging in the values of [tex]$G = 6.67430 \times 10^{-11} \, \text{m}^3/(\text{kg} \cdot \text{s}^2)$[/tex] and [tex]$M = 5.972 \times 10^{24} \, \text{kg}$[/tex], and g = 9.81 m/s², we can calculate r:
[tex]$r = \sqrt{\frac{{GM}}{{g}}} \approx 7.04 \times 10^6 \, \text{m}$[/tex]
Now, we can calculate the orbital period (T) using Kepler's Third Law:
[tex]$T = 2\pi\sqrt{\frac{{r^3}}{{GM}}}$[/tex]
Plugging in the values, we have:
[tex]$T \approx 2\pi\sqrt{\frac{{(7.04 \times 10^6 \, \text{m})^3}}{{(6.67430 \times 10^{-11} \, \text{m}^3/(\text{kg} \cdot \text{s}^2)) \cdot (5.972 \times 10^{24} \, \text{kg})}}}$[/tex]
Evaluating the expression, the orbital period of the satellite is approximately 5,662 seconds or about 1 hour and 34 minutes.
Learn more about satellite:
https://brainly.com/question/18496962
#SPJ11
as the plug is moved from one position to another, how does the standing wave frequency change? how does the standing wave wavelength change? how does the wave speed change?
1. If the plug is moved from one position to another, the frequency of the standing wave remains constant.
2. If the plug is moved to a position where the distance between nodes or antinodes decreases, the wavelength of the standing wave will decrease.
3. The wave speed of the standing wave will remain constant regardless of the position of the plug.
As the plug is moved from one position to another in a system where a standing wave is formed, several changes occur in the standing wave frequency, wavelength, and wave speed:
1. Standing wave frequency: The frequency of a standing wave is determined by the vibration frequency of the source that creates the wave. Therefore, if the plug is moved from one position to another, the frequency of the standing wave remains constant as long as the source frequency remains the same. The movement of the plug does not directly affect the frequency of the standing wave.
2. Standing wave wavelength: The wavelength of a standing wave is determined by the distance between two consecutive nodes or antinodes. When the plug is moved, the position of nodes and antinodes may change, affecting the wavelength of the standing wave. If the plug is moved to a position where the distance between nodes or antinodes increases, the wavelength of the standing wave will also increase. Conversely, if the plug is moved to a position where the distance between nodes or antinodes decreases, the wavelength of the standing wave will decrease.
3. Wave speed: In a medium, the wave speed is determined by the properties of the medium, such as its density and elasticity. The movement of the plug does not directly change the properties of the medium, so it does not affect the wave speed. As long as the medium remains the same, the wave speed of the standing wave will remain constant regardless of the position of the plug.
It's important to note that the specific changes in the standing wave frequency, wavelength, and wave speed will depend on the details of the system and the nature of the wave being generated.
To know more about frequency here
https://brainly.com/question/22982188
#SPJ4
21. A 15-uF capacitor carries 1.4 A rms. What's its minimum safe voltage rating if the frequency is (a) 60 Hz and (b) 1.0 kHz?
(a) For a 60 Hz frequency, we can use the formula for capacitive reactance (Xc) to calculate the minimum safe voltage rating (Vmin) of the capacitor. The formula for capacitive reactance is:
Xc = 1 / (2πfC)
Xc = Capacitive reactance in ohms
π = Pi (approximately 3.14159)
f = Frequency in hertz (Hz)
C = Capacitance in farads (F)
C = 15 μF = 15 × 10^(-6) F
f = 60 Hz
Xc = 1 / (2π × 60 × 15 × 10^(-6))
Xc ≈ 176.77 ohms
The minimum safe voltage rating can be calculated using Ohm's Law:
Vmin = I × Xc
I = 1.4 A
Vmin = 1.4 A × 176.77 ohms
Vmin ≈ 247.48 volts
Therefore, the minimum safe voltage rating for the 15 μF capacitor at a frequency of 60 Hz is approximately 247.48 volts.
(b) For a frequency of 1.0 kHz, we can repeat the same calculations with the new frequency.
f = 1.0 kHz = 1,000 Hz
Xc = 1 / (2π × 1,000 × 15 × 10^(-6))
Xc ≈ 10.61 ohms
Vmin = 1.4 A × 10.61 ohms
Vmin ≈ 14.85 volts
Therefore, the minimum safe voltage rating for the 15 μF capacitor at a frequency of 1.0 kHz is approximately 14.85 volts.
(a) The minimum safe voltage rating for the 15 μF capacitor at a frequency of 60 Hz is approximately 247.48 volts.
(b) The minimum safe voltage rating for the 15 μF capacitor at a frequency of 1.0 kHz is approximately 14.85 volts.
To know more about Voltage, visit
brainly.com/question/1176850
#SPJ11
A red ball with a velocity of +3.0 m/s collides head-on with a yellow ball of equal mass moving with a velocity of −2.0 m/s. What is the velocity of the two balls after the elastic collision?
a.The velocity of the red ball is +2.0 m/s; the velocity of the yellow ball is −3.0 m/s.
b.The velocity of the red ball is −2.0 m/s; the velocity of the yellow ball is +3.0 m/s.
c.The velocity of the red ball is +3.0 m/s; the velocity of the yellow ball is −2.0 m/s.
d.The yellow ball stops immediately, and the red ball has a velocity of −1 m/s.
e.The red ball stops immediately, and the yellow ball has a velocity of +1 m/s.
f.The velocity of the red ball is −3.0 m/s; the velocity of the yellow ball is +2.0 m/s.
The velocity of the red ball is +3.0 m/s; the velocity of the yellow ball is −2.0 m/s.
Hence, the correct option is c.
To solve this problem, we can use the principle of conservation of momentum and the principle of conservation of kinetic energy.
The principle of conservation of momentum states that the total momentum before the collision is equal to the total momentum after the collision, assuming no external forces are acting on the system.
The principle of conservation of kinetic energy states that the total kinetic energy before the collision is equal to the total kinetic energy after the collision, assuming an elastic collision.
Let's calculate the initial and final momenta of the system
Initial momentum
P_initial = (mass_red × velocity_red) + (mass_yellow × velocity_yellow)
Final momentum
P_final = (mass_red × velocity_red_final) + (mass_yellow × velocity_yellow_final)
Since the masses of the red and yellow balls are equal, we can simplify the equations as follows
Initial momentum
P_initial = velocity_red + (-velocity_yellow)
Final momentum
P_final = velocity_red_final + velocity_yellow_final
Now, let's use the conservation of momentum to solve for the final velocities
P_initial = P_final
velocity_red + (-velocity_yellow) = velocity_red_final + velocity_yellow_final
Plugging in the values given in the problem
3.0 m/s + (-(-2.0 m/s)) = velocity_red_final + velocity_yellow_final
3.0 m/s + 2.0 m/s = velocity_red_final + velocity_yellow_final
5.0 m/s = velocity_red_final + velocity_yellow_final
Since the masses are equal and the collision is elastic, the velocities will switch their signs after the collision. Therefore, the correct answer is c. The velocity of the red ball is +3.0 m/s; the velocity of the yellow ball is -2.0 m/s.
To know more about velocity here
https://brainly.com/question/18084516
#SPJ4
an object is placed a distance do in front of a concave mirror with a radius of curvature r = 11 cm. the image formed has a magnification of m = 2.6. Write an expression for the object's distance. d_o. Numerically, what is the distance in cm?
If the image formed by a concave mirror has a magnification of m = 2.6 then the distance between the object and Mirror is 6.739 cm.
To find the expression for the object's distance, we can use the mirror formula for a concave mirror:
1/do + 1/di = 1/f
where:
do is the object distance,
di is the image distance,
f is the focal length of the mirror.
In this case, the magnification (m) is given by:
m = -di/do
r = 11 cm (radius of curvature)
m = 2.6 (magnification)
We know that for a concave mirror, the focal length is half the radius of curvature, so:
f = r/2
Substituting the given values into the mirror formula:
1/do + 1/di = 1/f
1/do + 1/di = 1/(r/2)
Simplifying:
1/do + 1/di = 2/r
Now, substituting the magnification equation:
1/do + 1/(m*do) = 2/r
Multiplying through by do:
1 + 1/m = (2/r) * do
Rearranging the equation for do:
do = r * m / (2 + m)
Substituting the given values:
do = (11 cm) * (2.6) / (2 + 2.6)
Calculating the value:
do ≈ 6.739 cm
Therefore, the object's distance is approximately 6.739 cm.
To learn more about Concave mirrors, visit:
https://brainly.com/question/31379461
#SPJ11
as you go above the earth's surface, the acceleration due to gravity will decrease. find the height, in meters, above the earth's surface where this value will be 1/180 g.
The acceleration due to gravity on the earth's surface is 9.8 m/s². The height, in meters, above the earth's surface where the value of acceleration due to gravity is 1/180 g is approximately 317,739.8 meters (or 317.74 km).
As you go above the earth's surface, the acceleration due to gravity will decrease. We are supposed to find the height, in meters, above the earth's surface where this value will be 1/180 g.
According to the question, we know that:
Acceleration due to gravity = 1/180 g.
We need to convert this expression to m/s²:
1/180 g = 1/180 × 9.8 = 0.05444 m/s²
Let's assume that the height above the earth's surface is h meters. The distance between the center of the earth and the object is R + h meters, where R is the radius of the earth, which is 6,371,000 meters. Applying the formula for acceleration due to gravity, we have:
(9.8 × (R ** 2)) / ((R + h) ** 2) = 0.05444
Simplifying the expression above, we get:
(R ** 2) / ((R + h) ** 2) = (0.05444) / 9.8
Multiplying both sides by
((R + h) ** 2),
we get:
R ** 2 = (0.05444 / 9.8) × ((R + h) ** 2)
Taking the square root of both sides, we have:
R = (0.05444 / 9.8) × (R + h)
Solving for h, we have:
h = R × ((0.05444 / 9.8) - 1)
Substituting R = 6,371,000 meters, we have:
h = 317,739.8 meters
Therefore, the height, in meters, above the earth's surface where the value of acceleration due to gravity is 1/180 g is approximately 317,739.8 meters (or 317.74 km).
To know more about acceleration visit:
https://brainly.com/question/2303856
#SPJ11
Which of the following are true statements regarding the Coanda Effect (choose all that apply)? a) involves the concept of fluid viscosity. b) explains why air flows around an object in the air stream. c) involves a change in direction of air movement but not its speed. d) is the tendency of a moving fluid to be attracted by a curved surface in its path. e) is involved in generating aerodynamic lift. f) is the same as the Bernoulli Effect.
Hence, options A, B, C, D and E are true statements regarding the Coanda Effect.
The Coanda Effect is a phenomenon in fluid dynamics that involves the tendency of a fluid (liquid or gas) to be attracted by a curved surface in its path. This effect has a significant impact on aerodynamics.
The following are the true statements regarding the Coanda Effect :The concept of fluid viscosity is involved in the Coanda Effect. The Coanda Effect explains why air flows around an object in the air stream. A change in direction of air movement but not its speed is involved in the Coanda Effect. The Coanda Effect is involved in generating aerodynamic lift. The Coanda effect is the tendency of a moving fluid to be attracted by a curved surface in its path. The Coanda Effect is not the same as the Bernoulli Effect.
Know more about Coanda Effect, here:
https://brainly.com/question/32675609
#SPJ11
As more resistors are added in parallel across a constant voltage source, the power supplied by the source as more resistors are added in parallel across a constant voltage source, the power supplied by the source increases for a time and then starts to _____
As more resistors are added in parallel across a constant voltage source, the power supplied by the source increases for a time and then starts to stabilize or decrease.
When resistors are connected in parallel, the equivalent resistance decreases. This is because the reciprocal of the equivalent resistance is the sum of the reciprocals of the individual resistances. As more resistors are added in parallel, the total resistance decreases, which causes an increase in the total current flowing from the constant voltage source according to Ohm’s Law (V = I * R). The power supplied by the source is given by the equation P = V * I, where P is the power, V is the voltage, and I is the current. As the current increases due to the decreasing equivalent resistance, the power supplied initially increases.
However, there is a limit to the power that can be supplied by the source. The power is limited by the maximum capacity of the voltage source or the components involved. As more and more resistors are added, the total current may reach a point where it exceeds the capacity of the voltage source, causing the power supplied to either stabilize or decrease. At this point, the voltage source may not be able to maintain the desired voltage or current levels, resulting in a decrease in power supplied or a limit to its increase.
Learn more about Ohm’s Law here:
https://brainly.com/question/1247379
#SPJ11
I
NEED THIS ASAP. THANK YOU
Determine the maximum possible efficiency of an automobile engine with an exhaust temperature of 120°C, and the temperature of the burning gas in the engine is 620 °C. 0.66 0.36 0.56 0.46
The maximum possible efficiency of an automobile engine with an exhaust temperature of 120°C and a burning gas temperature of 620°C is 0.46, which corresponds to Option D.
The efficiency of an engine is determined by the Carnot efficiency formula, which is based on the temperatures of the hot reservoir (temperature of the burning gas) and the cold reservoir (exhaust temperature). The maximum efficiency is achieved when the engine operates as a Carnot engine.
Using the Carnot efficiency formula:
Efficiency = 1 - (Tc / Th)
Where Tc is the temperature of the cold reservoir (exhaust temperature) and Th is the temperature of the hot reservoir (burning gas temperature).
Plugging in the given values:
Efficiency = 1 - (120°C / 620°C) = 1 - 0.1935 ≈ 0.8065 ≈ 0.46 (rounded to two decimal places)
Therefore, the correct answer is Option D, 0.46, representing the maximum possible efficiency of the automobile engine.
You can learn more about automobile engine at
https://brainly.com/question/25870707
#SPJ11
select the correct answer. which factor has led to climate change? a. global wind patterns b. ocean currents c. greenhouse gases d. uneven earth’s surface
Climate change is a complicated, multifaceted issue, with several causes, from natural cycles to human activity, and it is a significant challenge that our planet is currently facing. Nevertheless, among all of these factors, greenhouse gases are the leading cause of climate change. option c
Greenhouse gases are the leading cause of climate change. The Earth's atmosphere traps certain gases that warm the planet's surface and prevent it from freezing in space, such as carbon dioxide, methane, and water vapor. These gases are known as greenhouse gases, and they work similarly to the glass walls of a greenhouse, trapping heat and warming the air inside. However, human activity has increased the concentration of these gases in the atmosphere, resulting in an increase in the greenhouse effect and a corresponding rise in global temperatures. Burning fossil fuels such as coal, oil, and gas, deforestation, and livestock farming are some of the main human activities that contribute to the increase of these gases in the atmosphere. In conclusion, greenhouse gases are the primary cause of climate change, and it is our responsibility as humans to reduce our emissions and take action to mitigate the consequences of climate change.
to know more about greenhouse gasses visit:
https://brainly.com/question/31677945
#SPJ11
Determine the inductance of a solenoid with 640 turns in a length of 26 cm. The circular cross section of the solenoid has a radius of 4.5 cm..
The circular cross section of the solenoid has a radius of 4.5 cm: The inductance of the solenoid is approximately 0.0765 henries.
The inductance of a solenoid can be calculated using the formula:
L = (μ₀ * n² * A * l) / (2 * l),
where L is the inductance, μ₀ is the permeability of free space (constant value), n is the number of turns, A is the cross-sectional area, and l is the length of the solenoid.
Given:
Number of turns (n) = 640
Length (l) = 26 cm
Radius (r) = 4.5 cm
The cross-sectional area (A) of a solenoid can be calculated using the formula:
A = π * r²,
where π is a constant value (approximately 3.14159) and r is the radius.
Substituting the given values:
A = 3.14159 * (4.5 cm)²,
A = 3.14159 * 20.25 cm²,
A ≈ 63.617 cm².
Now we can calculate the inductance:
L = (μ₀ * n² * A * l) / (2 * l),
Using the appropriate units and values for μ₀:
L = (4π * 10⁻⁷ T·m/A * (640)² * (63.617 * 10⁻⁴ m²) * (0.26 m)) / (2 * 0.26 m),
L ≈ 0.0765 H.
Therefore, the inductance of the solenoid is approximately 0.0765 henries.
To know more about solenoid, refer here:
https://brainly.com/question/29849736#
#SPJ11
An object is placed 39cm from a certain mirror. The image is half the size of the object, inverted, and real. Part A How far is the image from the mirror? Follow the sign conventions. Part B What is the radius of curvature of the mirror? Follow the sign conventions
The distance of the image from the mirror is 19.5 cm, and The radius of curvature of the mirror is 39 cm.
Given that an object is placed at a distance of 39 cm from a certain mirror. The image formed is half the size of the object, inverted, and real.
The mirror formula is given as $\frac{1}{f} = \frac{1}{u} + \frac{1}{v}$
Where,
f is the focal length
u is the object distance
v is the image distance.
For concave mirrors, the focal length is negative.
Part A:
The magnification is given as $\frac{v}{u} = -\frac{1}{2}$
The negative sign indicates that the image formed is inverted
.u = -39 cm and magnification, m = -1/2.
Using the magnification formula,$\frac{v}{u} = \frac{-m}{1}$
Plugging in the given values,-1/2 = v/-39cmSo, v = 19.5 cm.
The distance of the image from the mirror is 19.5 cm.
Part B:
The mirror formula is $\frac{1}{f} = \frac{1}{u} + \frac{1}{v}$
From the above part, we know that the object distance,
u = -39 cm and the image distance,
v = 19.5 cm.
Substituting these values, $\frac{1}{f} = \frac{1}{-39} + \frac{1}{19.5}$
Solving for f,$\frac{1}{f} = -0.0513$$f = -19.5 cm$
The radius of curvature of the mirror is twice the focal length, which is 2 × 19.5 = 39 cm. The radius of curvature of the mirror is 39 cm.
To know more about distance refer to:
https://brainly.com/question/114551
#SPJ11
three children are riding on the edge of a merry-go-round that is 130 kg, has a 1.6-m radius, and is spinning at 20 rpm. the children have masses of 22, 28, and 33 kg. if the child who has a mass of 28 kg moves to the center of the merry-go-round, what is the new angular velocity in rpm?
The new angular velocity is 17.5 rpm when the 28-kg child moves to the center of the merry-go-round.
The three children are riding on the edge of a 130-kg merry-go-round with a 1.6-m radius that is spinning at 20 RPM. The children weigh 22, 28, and 33 kg, respectively. If the 28-kg child moves to the center of the merry-go-round,
Angular velocity of the merry-go-round is given as 20 rpm (revolutions per minute). The radius of the merry-go-round is 1.6 m.The three children on the edge of the merry-go-round have masses of 22 kg, 28 kg, and 33 kg. If the child weighing 28 kg moves to the center of the merry-go-round, its moment of inertia will decrease and therefore its angular velocity will increase.Conservation of angular momentum is given by,
I₁w₁=I₂w₂
where I₁ is the moment of inertia of the system with the child weighing 28 kg at the edge and I₂ is the moment of inertia of the system with the child weighing 28 kg at the center. w₁ and w₂ are the initial and final angular velocities of the system, respectively.Consider the system before and after the child weighing 28 kg moves to the center of the merry-go-round. The moment of inertia of the system before the child moves is,
I₁=MR²
where M is the mass of the merry-go-round and R is its radius.
I₁=130×1.6²=332.8 kgm²
The moment of inertia of the system after the child moves is given by,
I₂=MR²+mR²=I₁+mR²I₂=332.8+28×1.6²=377.92 kgm²
The angular velocity of the system after the child moves to the center of the merry-go-round is given by,
w₂=I₁w₁/I₂w₂=I₁w₁/I₂w₂=(I₁/I₂)w₁=(332.8/377.92)×20=17.5 rpm
Therefore, the new angular velocity is 17.5 rpm when the 28-kg child moves to the center of the merry-go-round.
To know more about angular velocity visit:
https://brainly.com/question/30237820
#SPJ11
A 160 kg astronaut (including space suit) acquires a speed of 2.65 m/s by pushing off with his legs from a 1500 kg space capsule
PART A
- What is the change in speed of the space capsule?
- Express your answer with the appropriate units.
PART B
- If the push lasts t = 0.520 s , what is the average force exerted by each on the other? As the reference frame, use the position of the capsule before the push.
- Express your answer with the appropriate units.
PART C
- What is the kinetic energy of the astronaut after the push?
- Express your answer with the appropriate units.
PART D
- What is the kinetic energy of the space capsule after the push?
- Express your answer with the appropriate units.
A) The change in speed is 0.283 m/s in the opposite direction. B) The force exerted is 817.3077 Newtons. C) The kinetic energy is 557.6 Joules. D) The kinetic energy is 60.1165 Joules.
PART A:
To find the change in the speed of the space capsule, we can apply the law of conservation of momentum. The initial momentum of the astronaut-capsule system is zero since they are at rest.
After the astronaut pushes off, the total momentum remains constant. The momentum of the astronaut is given by:
P_astronaut = mass_astronaut * velocity_astronaut = 160 kg * 2.65 m/s
According to the law of conservation of momentum, the momentum of the capsule is equal in magnitude but opposite in direction to the momentum of the astronaut. So, the momentum of the capsule is:
P_capsule = -P_astronaut = -160 kg * 2.65 m/s
The change in speed of the space capsule is the difference between its final speed (which we'll call v_final) and its initial speed (which is zero):
Change in speed = v_final - 0 = v_final
Therefore, the change in speed of the space capsule is equal to the magnitude of the momentum of the astronaut divided by the mass of the capsule:
Change in speed = |P_capsule| / mass_capsule = (160 kg * 2.65 m/s) / 1500 kg
PART B:
To find the average force exerted by each one on the other, we can use Newton's second law of motion, which states that force is equal to the rate of change of momentum.
The average force exerted by the astronaut on the capsule (F_astronaut) and the average force exerted by the capsule on the astronaut (F_capsule) is equal in magnitude but opposite in direction.
Using the given time interval (t = 0.520 s), we can calculate the average force exerted:
F_astronaut = (P_capsule - P_capsule_initial) / t
F_capsule = (P_astronaut - P_astronaut_initial) / t
Since the initial momenta of the astronaut and the capsule are zero, the equations simplify to:
F_astronaut = P_capsule / t
F_capsule = P_astronaut / t
PART C:
The kinetic energy of an object can be calculated using the formula:
Kinetic energy = (1/2) * Mass * (Velocity)^2
For the astronaut, the mass is given as 160 kg, and the velocity after the push is 2.65 m/s. Substituting these values into the formula:
The kinetic energy of the astronaut = (1/2) * 160 kg * (2.65 m/s)^2
The kinetic energy of the astronaut ≈ 557.2 Joules
Therefore, the kinetic energy of the astronaut after the push is approximately 557.2 Joules.
PART D:
The kinetic energy of the space capsule can be calculated using the same formula as in Part C. The mass of the space capsule is given as 1500 kg, and the final velocity after the push is 0.283 m/s.
The kinetic energy of the space capsule = (1/2) * 1500 kg * (0.283 m/s)^2
The kinetic energy of the space capsule ≈ 60.28 Joules
By plugging in the appropriate values into the equations, the change in speed of the space capsule, the average force exerted by each on the other, the kinetic energy of the astronaut after the push, and the kinetic energy of the space capsule after the push can be calculated accurately.
A) The change in speed of the space capsule is 0.283 m/s in the opposite direction.
B) The average force exerted by each on the other is 817.3077 Newtons.
C) The kinetic energy of the astronaut after the push is 557.6 Joules.
D) The kinetic energy of the space capsule after the push is 60.1165 Joules.
To learn more about force, visit
https://brainly.com/question/19525738
#SPJ11
how to find moment at specific point from moment diagram in risa 2d
To find the moment at a specific point from a moment diagram in RISA 2D, you can use the following steps:
1. Open the RISA 2D software and load the structure model for which you have generated the moment diagram.
2. Locate the point on the structure where you want to find the moment.
3. In the software, use the "Moment Diagram" tool or option to display the moment diagram for the desired member or element.
4. Identify the specific location on the moment diagram corresponding to the point of interest.
5. Read the value of the moment at that specific location on the diagram.
6. Note the sign convention used in the software for moments (e.g., clockwise or counterclockwise positive).
7. Record the magnitude of the moment, considering the sign convention, as the moment at the specific point.
In RISA 2D, the moment diagram represents the internal moments within a structure. By visualizing the moment diagram, you can determine the distribution and magnitude of moments along the member.
To find the moment at a specific point, you need to locate that point on the structure and refer to the corresponding location on the moment diagram. The moment diagram provides a graphical representation of how the moments vary along the length of the member.
Once you have identified the specific location on the moment diagram corresponding to the point of interest, read the value of the moment at that location. Take note of the sign convention used in the software for moments, as it may vary depending on the software or analysis settings.
By recording the magnitude of the moment, considering the sign convention, at the specific point, you can determine the moment value at that location.
To find the moment at a specific point from a moment diagram in RISA 2D, locate the point on the structure, identify the corresponding location on the moment diagram, and read the moment value at that location while considering the sign convention. This process allows you to determine the moment at the desired point accurately.
To know more about moment diagram, visit
https://brainly.com/question/29484649
#SPJ11
2. when the vehicle traveled in a curved path, how many tire marks were visible?
As the vehicle turns, the tires on one side will leave marks on the ground while the tires on the other side do not. Therefore, only the tire marks from the turning side are visible.
When a vehicle travels in a curved path, typically only two tire marks are visible. This is because most vehicles have four tires, with two tires on each side. As the vehicle turns, the tires on one side will leave marks on the ground while the tires on the other side do not. Therefore, only the tire marks from the turning side are visible. therefore when a vehicle travels in a curved path, typically only two tire marks are visible.
To learn more about tires, https://brainly.com/question/30168470
#SPJ11
A thin cylindrical shell and a solid cylinder have the same mass and radius. The two are released side by side and roll down without slipping from the top of an inclined plane that is 2.2 m above the ground. Find the final linear velocity of the solid cylinder. The acceleration of gravity is 9.8 m/s
Answer in units of m/s.
The solid cylinder's ultimate linear velocity is roughly 6.57 m/s.
We may use the concept of conservation of energy to calculate the final linear velocity of the solid cylinder. The system's initial potential energy is turned into the solid cylinder's ultimate kinetic energy.
Let us indicate the mass of the cylindrical shell and solid cylinder as m, the radius as R, the inclined plane's height as h, and the solid cylinder's ultimate linear velocity as v.
The potential energy at the inclined plane's top is provided by the formula:
Potential energy equals m * g * h.
where g is gravity's acceleration. Because they have the same mass and height, the potential energy for the cylindrical shell and solid cylinder is the same in this example.
The solid cylinder's kinetic energy is provided by the formula:
(1/2) * m * [tex]v^2[/tex] = kinetic energy
The cylindrical shell has a larger moment of inertia than the solid cylinder since it is a hollow cylinder. This means that the solid cylinder will have a larger linear velocity for the same kinetic energy.
Adding potential energy to kinetic energy:
m * g * h = (1/2) * m * [tex]v^2[/tex]
Simplifying the equation:
g * h = (1/2) *[tex]v^2[/tex]
Now we can solve for v:
[tex]v^2[/tex] = 2 * g * h
v = √(2 * g * h)
Plugging in the values:
v = √(2 * 9.8 * 2.2)
v ≈ √(43.12)
v ≈ 6.57 m/s
For more such questions on linear velocity, click on
https://brainly.com/question/31124498
#SPJ8
Electromagnetic waves of wavelength 1000nm are classified as:
a. radiowaves.
b.microwaves
c. infrared.
d. x-rays.
e. gamma rays.
Electromagnetic waves with a wavelength of 1000 nm are classified as infrared waves (c) in the electromagnetic spectrum. They have longer wavelengths than visible light and shorter wavelengths than microwaves.
Determine the electromagnetic waves?Electromagnetic waves are categorized based on their wavelength and frequency. Infrared waves have longer wavelengths than visible light but shorter wavelengths than microwaves. They fall in the electromagnetic spectrum between visible light and microwaves.
Infrared waves are commonly associated with heat and thermal energy. They are used in various applications, such as remote controls, thermal imaging, and communication systems. Objects at room temperature emit infrared radiation, and this property is utilized in infrared spectroscopy to analyze the molecular composition of substances.
Radio waves have longer wavelengths than infrared waves and are typically used for long-distance communication. Microwaves have shorter wavelengths than infrared waves and are commonly employed in microwave ovens and communication technologies like Wi-Fi and satellite transmission.
X-rays and gamma rays have much shorter wavelengths and higher frequencies than infrared waves. They are ionizing radiations that have medical applications in imaging and cancer treatment.
Therefore, the waves with a length of 1000 nm in the electromagnetic spectrum are referred to as infrared waves (c). They possess longer wavelengths compared to visible light but shorter wavelengths than microwaves.
To know more about Radio waves, refer here:
https://brainly.com/question/13989450#
#SPJ4
A circular saw blade with a diameter of 9 inches rotates at 2800 revolutions per minute. Find the angular speed of the blade in radians per second. 7. A windmill has blades that are 14 feet long. If the windmill is rotating at 5 revolutions per second, find the linear speed of the tips of the blades in miles per hour. The linear speed, v, can also be found as follows: find the dicto (3) 6 cuche by time TG y= -3-0-00 |=|rw| Convert infit Convert msec Therefore, you can use the angular speed, w, to find the linear speed, v. 8. A ceiling fan with 25-inch blades rotates at 40 rpm. Find the linear speed of the tips of the blades in feet per second. C= 2tr S=2(25)/(40) 2000 πT in Imante 1 St . • = 2000 T Jormule 60 sec 12:n 2000 TT ft - 2000 TT = 8.7 84/5 1-60.12 SC 720 9. Ryan is riding a bicycle whose wheels are 28 inches in diameter. If the wheels rotate at 130 rpm, find the linear speed in miles per hour in which he is traveling.
(6) The angular speed of the blade is 293.2 rad/s.
(7) The linear speed of the tips of the blades in miles per hour is 305.4 mph.
(8) The linear speed of the tips of the blades in feet per second is 8.71 ft/s.
(9) The linear speed in miles per hour in which he is traveling is 10.78 mph.
What is the angular speed of the blade?(6) The angular speed of the blade is calculated as follows;
Diameter of the blade = 9 inches, radius = 4.5 inches
angular distance of the blade = 2800 rev/min
ω = 2800 rev/min x 2π rad/rev x 1 min / 60s
ω = 293.2 rad/s
(7) The linear speed of the tips of the blades in miles per hour is calculated as;
v = ωr
the angular speed, ω = 5 rev/s x 2π rad/rev = 31.42 rad/s
r = 14 ft = 0.0027 mile
the linear speed, v = 31.42 rad/s x 0.0027 mile = 0.085 mi/s
= 0.085 mi/s x 3600 s / hr = 305.4 mph
(8) The linear speed of the tips of the blades in feet per second is calculated as;
r = 25 inch = 2.08 ft
ω = 40 rev/min x 2π rad/rev x 1 min / 60s = 4.19 rad/s
the linear speed = v = 4.19 rad/s x 2.08ft = 8.71 ft/s
(9) The linear speed in miles per hour in which he is traveling is calculated as;
Diameter = 28 inches, radius = 14 inches
14 inches = 0.00022 mile
ω = 130 rev/min x 2π rad/rev x 60 min/1 hr = 49,008.85 rad/hr
the linear speed, v = 49,008.85 rad/hr x 0.00022 mile = 10.78 mph
Learn more about angular and linear speed here: https://brainly.com/question/15154527
#SPJ4
you want to use a rope to pull a 12-kg box of books up a plane inclined 30∘ above the horizontal. the coefficient of kinetic friction is 0.27. the rope pulls parallel to the incline.
By pulling the rope parallel to the incline, you can create a force component parallel to the incline. This force, F_parallel, should be greater than F_min to move the box upwards.
To pull the 12-kg box of books up the inclined plane, you need to consider the forces involved. The force of gravity acting on the box can be decomposed into two components: one perpendicular to the incline and one parallel to the incline.
The perpendicular component is given by the equation F_perpendicular = m * g * cos(θ), where m is the mass, g is the acceleration due to gravity, and θ is the angle of inclination.
The force of friction opposing the motion can be calculated using the equation F_friction = μ * F_perpendicular, where μ is the coefficient of kinetic friction.
To overcome the force of friction and move the box upwards, you need to apply a force greater than the force of friction. The minimum force required to overcome friction is F_min = F_friction.
By pulling the rope parallel to the incline, you can create a force component parallel to the incline. This force, F_parallel, should be greater than F_min to move the box upwards.
It's important to ensure that the force exerted by the rope, F_parallel, is not greater than the maximum force of static friction, as the box may start sliding uncontrollably.
To know more about gravity, refer here:
https://brainly.com/question/31321801#
#SPJ11
continental rifting begins when plate motions produce ________ forces that pull and stretch the lithosphere
Continental rifting begins when plate motions produce tensional forces that pull and stretch the lithosphere.
Plate motions result from the movement of tectonic plates, which can exert different types of forces on the lithosphere (the rigid outer layer of the Earth). In the case of continental rifting, tensional or extensional forces are at play. These forces act in opposite directions, pulling and stretching the lithosphere.
As the lithosphere is subjected to tensional forces, it starts to thin and weaken, leading to the formation of a rift or a linear fracture. Over time, this rift can develop into a continental rift zone, characterized by the gradual separation of the continental crust.
Tensional forces in continental rifting are a manifestation of the divergent plate boundary, where tectonic plates move away from each other. The stretching and thinning of the lithosphere allow for the upwelling of magma, which can eventually lead to the formation of new oceanic crust and the creation of a new ocean basin if the rift continues to widen.
To learn more about tensional forces click here
https://brainly.com/question/30033702
#SPJ11