a stone is dropped from the top of a cliff. the splash it makes when striking the water below is heard 2.7 s later. how high is the cliff?

The radii of the pedal sprocket, the wheel sprocket, and the wheel of a bicycle can vary depending on the specific bicycle model and design.

There is no standard or fixed value for these radii as they can differ from one bicycle to another. The radii are typically determined by the manufacturer and are based on factors such as the intended use of the bicycle, gear ratios, and desired performance characteristics. The pedal sprocket is the smaller sprocket attached to the pedals of the bicycle. It is responsible for transferring the rider's pedaling force to the drivetrain of the bicycle. The radius of the pedal sprocket is generally smaller compared to the wheel sprocket and wheel. The wheel sprocket, also known as the rear sprocket or cassette, is located on the rear wheel of the bicycle. It engages with the chain and is responsible for transferring power from the pedals to the wheel. The radius of the wheel sprocket is usually larger compared to the pedal sprocket.

To learn more about specific bicycle model, Click here:

https://brainly.com/question/13308530

#SPJ11

When the energy stored in an inductor is at a maximum, the energy stored in the capacitor is zero. In an oscillating circuit consisting of an inductor and a capacitor, energy continuously transfers back and forth between the inductor and the capacitor.

At any given moment, the total energy in the circuit remains constant. When the energy stored in the inductor is maximum, all the energy is stored in the inductor's magnetic field. At the same time, the energy stored in the capacitor is minimum, as the capacitor's electric field is at its minimum.

As the energy oscillates between the inductor and the capacitor, there is a point in the cycle where the energy stored in the inductor is zero and the energy stored in the capacitor is maximum. This occurs when the charge on the capacitor plates is maximum and the voltage across the capacitor is maximum.

In summary, when the energy stored in the inductor is at a maximum, the energy stored in the capacitor is zero.

To know more about the oscillating circuit refer here :

https://brainly.com/question/29045377#

#SPJ11

The 2018 Ford Explorer gets 22 miles per gallon (mpg), slightly better gas mileage than previous year’s models. In the case of the 2018 Ford Explorer, engineers and designers likely implemented design improvements and optimizations to enhance its fuel economy.

The 2018 Ford Explorer achieves a fuel efficiency of 22 miles per gallon (mpg), which represents a slight improvement compared to the gas mileage of previous year's models. This measurement indicates the distance in miles that the vehicle can travel on one gallon of fuel. With 22 mpg, the 2018 Explorer demonstrates enhanced fuel economy, which can be attributed to various factors such as advancements in engine technology, aerodynamics, and efficiency optimizations. These may include the use of lightweight materials to reduce vehicle weight, aerodynamic enhancements to reduce drag, and engine advancements such as improved combustion efficiency and transmission optimization. Collectively, these efforts contribute to the slight increase in gas mileage compared to previous models.

To learn more about fuel economy, Click here:

https://brainly.com/question/30724675

#SPJ11

Answer:

the answer is B I promise

Answer:

Period = 0.68 seconds

Explanation:

Given the following data;

Number of oscillation = 22

Time = 14.9 seconds

To find the period;

Method I.

Period = time/number of oscillation

Period = 14.9/22

Period = 0.68 seconds.

Method II.

We would find the frequency of the wave;

Frequency = time/number of oscillation

Frequency = 22/14.9

Frequency = 1.48 Hertz

Next, we find the period;

Period = 1/frequency

Period = 1/1.48

Period = 0.68 seconds

In the case of smoke detectors based on the radioactive decay of americium-241, the type of radiation emitted by the source is alpha radiation.

Alpha particles are composed of two protons and two neutrons, essentially the same as a helium nucleus. They have a positive charge and are relatively large and heavy compared to other types of radiation. Americium-241 undergoes alpha decay, where it spontaneously emits an alpha particle from its nucleus. This decay process results in the production of a daughter nucleus and the release of an alpha particle, which consists of two protons and two neutrons.  Alpha particles have a low penetrating power and can be easily stopped by a sheet of paper or a few centimeters of air. This characteristic makes them ideal for use in smoke detectors because they can ionize the air inside the detector chamber, allowing for the detection of smoke particles.

In contrast, beta and gamma radiation are not typically used in smoke detectors. Beta particles are high-energy electrons or positrons, while gamma rays are high-frequency electromagnetic waves. These types of radiation have higher penetrating power and would not be as effective in ionizing the air for smoke detection purposes. Therefore, the most likely type of radiation emitted by the americium-241 source in a smoke detector is alpha radiation.

Learn more about Alpha particles here:

https://brainly.com/question/24276675

#SPJ11

The statement " The effective capacity utilization can be smaller than the design capacity utilization." is True because design capacity utilization refers to the maximum utilization of the system's capacity under ideal conditions.

Effective capacity utilization refers to the actual utilization of a system's capacity, taking into account factors such as downtime, maintenance, and other operational constraints. On the other hand, design capacity utilization refers to the maximum utilization of the system's capacity under ideal conditions.

In practice, it is common for the effective capacity utilization to be smaller than the design capacity utilization. This occurs due to various factors that affect the actual production or service delivery. These factors can include equipment breakdowns, scheduled maintenance, employee absenteeism, supply chain disruptions, and variations in customer demand.

The effective capacity utilization considers the real-world operational conditions and takes into account the constraints and limitations that can impact the system's performance. Therefore, it is not uncommon for the effective capacity utilization to be lower than the design capacity utilization, which represents the theoretical maximum utilization achievable under ideal circumstances.

To know more about utilization, refer here:

https://brainly.com/question/14643660#

#SPJ11

To calculate the Coulomb energy and the repulsion energy for a NaCl ionic crystal at its equilibrium separation, we need to consider the ionic charges and the crystal lattice structure.

In NaCl, sodium (Na) has a +1 charge, and chloride (Cl) has a -1 charge. The crystal structure of NaCl is a face-centered cubic (FCC) lattice.

The Coulomb energy is the electrostatic interaction energy between the charged ions. It can be calculated using Coulomb's law:

Coulomb energy ([tex]E_{coul[/tex]) = (1 / 4πε₀) * Σ([tex]q_i * q_j[/tex]) / [tex]r_{ij[/tex]

Where:

ε₀ is the vacuum permittivity (8.854 × [tex]10^{-12}[/tex] C²/N·m²)

[tex]q_i[/tex]  and [tex]q_j[/tex] are the charges of the ions

[tex]r_{ij[/tex] is the distance between ions i and j

The repulsion energy arises from the repulsion between the ions due to overlapping electron clouds. It can be approximated using an empirical expression known as the Born-Mayer equation:

Repulsion energy ([tex]E_{rep[/tex]) = A * exp(-B * r)

Where:

A and B are empirical constants specific to the crystal

r is the distance between ions

Now, let's assume the equilibrium separation ([tex]r_{eq}[/tex]) for NaCl at room temperature, which is approximately 2.82 Å (angstroms).

Using these values, we can calculate the Coulomb energy and the repulsion energy for NaCl at its equilibrium separation. However, the specific values of A and B for NaCl are required to obtain an accurate result.

These values are not readily available, and their determination involves experimental measurements and/or computational calculations beyond the scope of this text-based conversation.

Therefore, without the precise values of A and B, we cannot provide an exact numerical calculation of the Coulomb energy and the repulsion energy for NaCl at its equilibrium separation.

To learn more crystal lattice structure visit:

brainly.com/question/30049286

#SPJ11

The image distance from the converging lens is 10.2 cm.

The focal length of the converging lens, f = 28 cm

The distance of the object from the converging lens, u = -16 cm

The optical center or axis of a convergent lens serves as the focal point for light, a lens that generates a real image by converting parallel light beams to convergent light rays.

The image is real and inverted so long as the item is not in the center of the lens.

According to the lens formula,

1/v + 1/u = 1/f

1/v = 1/f - 1/u

1/v = 1/28 - 1/-16

1/v = 1/28 + 1/16

1/v = 44/448

Therefore, the image distance from the converging lens is,

v = 448/44

v = 10.2 cm

To learn more about converging lens, click:

https://brainly.com/question/29178301

#SPJ4

The focal point of the solar cooker is 6.845 cm above the base.

For a parabolic reflector, the focal point (F) lies along the axis of symmetry, and the distance from the vertex to the focal point (the focus) is given by the equation:

4f = p

Where:

f = distance of the focal point from the vertex, and

p = depth of the paraboloid.

Given that the depth of the cooker is 27.38 cm, substitute this into the equation to find the focal point:

4f = 27.38 cm

f = 27.38 cm / 4

f = 6.845 cm

Therefore, the focal point of the solar cooker is 6.845 cm above the base.

Find out more on paraboloid here: https://brainly.com/question/32575113

#SPJ4

Answer:

this one is for your egg drop question

first question -

Use this worksheet to design your device and record your data. You can then use this form to help you  write your lab report.  

Height of egg drop: _5ft._

__________________________________________________________

Q2:

Ideas for Prototype Design

Teepee, large cube , small cube

__________________________________________________________

Q3:

Preliminary Sketches (attach separate paper if needed)

Option A: teepee

__________________________________________________________

Q4:

Advantages:                                           Disadvantages:  

● fully covered                  ● egg might crack

●  could stand higher distances    ●egg will most likely bounce around    around but not crack  but most likely to crack

__________________________________________________________

Q5:

Option B: large cube

Option C: smaller cube

__________________________________________________________

Q6:

more advantages and disadvantages

Advantages: Disadvantages:  

● egg will be tightly secured so nothing bounces around

●  egg might crack depending on the impact to the floor

__________________________________________________________

Q7:

Which of the three designs will you move forward with? Explain your reasoning for selecting this design.

I think i'm going to be moving forward with the teepee design

__________________________________________________________

Q8:

Building the Prototype  

What modifications, if any, did you make to the basic design during the construction process?

I made it a little smaller than the original design

__________________________________________________________

Q9:

Predictions  

Will your device cushion the egg? How will your device do this?

I think it will cushion the design if i put the plastic bag in with the egg it should prevent it from moving around to much

__________________________________________________________

Q10:

Will your device increase the time it takes for the egg to impact the ground? How will your device do this?

I think the extra weight added to the design might affect it by speeding up the process down to the floor

__________________________________________________________

Q11:

Observations  

Record your observations and the results of the experimental tests of your device below.

First i tried the egg without the plastic bag and it cracked so i made the design smaller and added the plastic bag this time

__________________________________________________________

Q12:

Evaluating Your Prototype  

What worked well? I would say definitely the plastic bag keeping the egg in place

__________________________________________________________

Q13:

Which features can be improved upon? The structure itself as in where the string and tape were

__________________________________________________________

Q14:

Suggestions  

How could the design of this device be improved? More balance i guess because the egg would move alot without the bag

__________________________________________________________

Q15:

Why would this change be an improvement? What force or momentum principle is this improvement  based on? If the egg had more balance then it would have a less chance of cracking i think this is a type of impulse toward the ground bc of the egg’s weight

__________________________________________________________

Q16:

Sketch of Final Design  

Draw a well-labeled sketch of the final design.

( i provided it :) )

okie peace!

Answer

slope

Explanation:

Answer: Medial rotation

Lateral rotation

Supination

Pronation

Opposition

Explanation:

Medial rotation can be defined as the rotation of any of the body part towards the middle axis of the body. For example, movement of leg bones so that the toes are pointed towards inward.

Lateral rotation is the movement of the body parts or bones away from the middle axis of the body. For example. outward circle created by the upper limbs directed outwards.

Supination is the rotation of the forearm in such a way so that the palm is directed upwards so that hand can receive money or hand can slap a person.

Pronation is the downward motion of hand to put things down.

Opposition is the movement of the bones of the fingers the metacarpals which allow the thumb to touch the fingertips.

The maximum value of the current in the circuit is approximately 0.1298 A. The maximum values of the potential difference across the resistor and the capacitor are equal to the maximum voltage (170 V) because they are in series with the AC source.

To solve this problem, we can use the concepts of AC circuit analysis and impedance.

Given:

Frequency (f) = 60 Hz

Maximum voltage [tex]\[V_\text{max}[/tex]) = 170 V

Resistance (R) = 1.2 kΩ = 1200 Ω

Capacitance (C) = 2.5 μF = 2.5 x 10⁻⁶ F

(a) The maximum value of the current in the circuit can be calculated using Ohm's law:

[tex]Imax = \frac{Vmax}{Z}[/tex]

where Z is the impedance of the circuit.

For a series RL circuit like this, the impedance Z is given by:

[tex]\[Z = \sqrt{R^2 + (X_c - X_l)^2}\][/tex]

where [tex]\[X_c[/tex] is the capacitive reactance and [tex]\[X_I[/tex] is the inductive reactance.

The capacitive reactance [tex]\[X_c[/tex] is given by:

[tex]\[X_c = \frac{1}{2\pi fC}\][/tex]

The inductive reactance Xl is given by:

Xl = 2πfL

However, since there is no inductor in the circuit (only a resistor and a capacitor), the inductive reactance is zero ([tex]\[X_I[/tex] = 0).

Substituting the values, we can calculate the maximum current:

[tex]\[X_c = \frac{1}{2\pi \cdot 60 \cdot 2.5 \cdot 10^{-6}}\][/tex]

   ≈ 530.66 Ω

[tex]\[Z = \sqrt{1200^2 + (530.66 - 0)^2}\][/tex]

  ≈ 1311.79 Ω

[tex]\[I_\text{max} = \frac{170 \text{ V}}{1311.79 \Omega}\][/tex]

     ≈ 0.1298 A

Therefore, the maximum value of the current in the circuit is approximately 0.1298 A.

(b) The maximum values of the potential difference across the resistor and the capacitor are equal to the maximum voltage ([tex]\[V_\text{max}[/tex]) because they are in series with the AC source. So:

Potential difference across the resistor = [tex]\[V_\text{max}[/tex]

Potential difference across the capacitor = [tex]\[V_\text{max}[/tex]

(c) When the current is zero, the potential difference across the resistor and the capacitor is zero because there is no current flowing through them. However, the potential difference across the AC source remains the same, which is the maximum voltage ([tex]\[V_\text{max}[/tex]). So:

Potential difference across the resistor = 0 V

Potential difference across the capacitor = 0 V

Potential difference across the AC source = [tex]\[V_\text{max}[/tex]

The magnitude of the potential difference across the AC source remains the same as the maximum voltage ([tex]\[V_\text{max}[/tex]).

To find the charge on the capacitor when the current is zero, we can use the equation:

Q = C * V

where Q is the charge, C is the capacitance, and V is the potential difference across the capacitor.

Q = (2.5 x 10⁻⁶ F) * 0 V

  = 0 C

Therefore, the charge on the capacitor when the current is zero is 0 C.

(d) When the current is at its maximum value ([tex]\[I_\text{max}[/tex]), the potential difference across the resistor is given by Ohm's law:

Potential difference across the resistor = [tex]\[I_\text{max}[/tex] * R

                                         = 0.1298 A * 1200 Ω

                                         = 155.76 V

The potential difference across the capacitor can be found using the equation:

Potential difference across the capacitor =[tex]\[I_\text{max}[/tex] * [tex]\[X_c[/tex]

Potential difference across the capacitor = 0.1298 A * 530.66 Ω

                                         = 69.75 V

The potential difference across the AC source remains the same as the maximum voltage ([tex]\[V_\text{max}[/tex]), which is 170 V.

To find the charge on the capacitor when the current is at its maximum, we can use the equation:

Q = C * V

Q = (2.5 x 10⁻⁶ F) * 69.75 V

  ≈ 0.0001744 C

Therefore, the charge on the capacitor when the current is at its maximum is approximately 0.0001744 C.

To know more about the maximum voltage refer here :

https://brainly.com/question/2921287#

#SPJ11

The intensity (mGya) resulting at 400 cm SID, with a constant mAs of 120 is 75 mGya.

According to the inverse square law, the intensity of radiation is inversely proportional to the square of the distance. The formula to calculate the intensity is:

Intensity2 = Intensity1 * (Distance1 / Distance2)^2

Given that the initial intensity (Intensity1) is 300 mR, the initial distance (Distance1) is 200 cm, and the final distance (Distance2) is 400 cm, we can substitute these values into the formula:

Intensity2 = 300 mR * (200 cm / 400 cm)^2 = 300 mR * (1/2)^2 = 300 mR * 1/4 = 75 mR

Since 1 Gy (Gray) is equal to 1000 mGy, the intensity at 400 cm SID is 75 mR, which is equivalent to 0.075 mGya.

You can learn more about inverse square law at

https://brainly.com/question/30404562

#SPJ11

Answer:

1. sand and water

2. suspension

mark me as brainliest plz

Option (A) because a force acts on it , is the correct option .

A space probe in remote outer space continues moving because a force acts on it.

According to Newton's first law of motion, an object will continue to move in a straight line at a constant velocity unless acted upon by an external force. In the case of a space probe in remote outer space, several forces can act on it to maintain its motion.

One of the significant forces at play is gravity. While space is mostly empty, gravitational forces from celestial bodies can still influence the probe's trajectory. If the probe is near a massive object like a planet or a star, the gravitational force exerted by that object can provide the necessary force to keep the probe moving. In this scenario, the probe would move in a curved path around the massive object due to the gravitational force acting as a centripetal force.

Additionally, other forces such as propulsion systems, solar radiation pressure, or gravitational assists from planetary flybys can also act on the space probe, ensuring its continued motion and trajectory adjustments.

A space probe in remote outer space continues moving due to the presence of external forces acting on it. These forces, such as gravity, propulsion systems, solar radiation pressure, or gravitational assists, provide the necessary force to counteract any potential deceleration or deviation from its intended path.

While the probe may move in a curved path due to gravitational forces, it ultimately remains in motion because forces act upon it. Therefore, option A) is the correct choice.

To know more about force ,visit:

https://brainly.com/question/12785175

#SPJ11

The magnitude of the force exerted by the tow bar on the skier can be calculated using the principles of Newton's second law and considering the forces acting on the skier. The force applied by the tow bar is equal to the sum of the gravitational force and the force of kinetic friction.

The gravitational force acting on the skier can be calculated as the product of the skier's mass (m) and the acceleration due to gravity (g), which is approximately 9.8 m/s². Thus, the gravitational force is given by [tex]F_{gravity} = m g[/tex].

The force of kinetic friction can be determined using the equation [tex]F_{friction} = \mu \times N[/tex], where μ is the coefficient of kinetic friction and N is the normal force. The normal force is equal to the component of the gravitational force perpendicular to the slope, which is given by [tex]N = mg cos(\theta)[/tex], where [tex]\theta[/tex] is the angle of inclination.

Since the skier is pulled up the slope at a constant velocity, the net force acting on the skier is zero. Therefore, the force exerted by the tow bar is equal in magnitude but opposite in direction to the sum of the gravitational force and the force of kinetic friction. Thus, the magnitude of the force exerted by the tow bar on the skier can be calculated as follows:

[tex]F_{\text{tow bar}} = F_{\text{gravity}} + F_{\text{friction}} \\\\F_{\text{tow bar}} = m \cdot g + \mu \cdot N \\\\\[ F_{\text{tow bar}} = m \cdot g + \mu \cdot m \cdot g \cdot \cos(\theta)[/tex]

Plugging in the given values: mass (m) = 50.7 kg, coefficient of kinetic friction (μ) = 0.144, angle of inclination [tex](\theta)[/tex] = 22.9°, and acceleration due to gravity (g) ≈ 9.8 m/s², we can calculate the magnitude of the force exerted by the tow bar on the skier.

To learn more about Newton's second law refer:

https://brainly.com/question/25545050

#SPJ11

An oscillator is an electronic device that produces an electrical signal at a specific frequency. A capacitor is an electrical component that stores electrical energy. In recent years, it has become possible to purchase a 1.0 F capacitor. This is an incredibly large amount of capacitance.

Suppose you want to build a 1.1 Hz oscillator using a 1.0 F capacitor and a spool of 0.25-mm-diameter wire and a 4.0-cm-diameter plastic cylinder. We can calculate the required inductance value using the formula:f = 1/2π√(L*C)Where f is the desired frequency, L is the inductance value, and C is the capacitance value. Substituting the given values:

[tex]f = 1.1 HzC = 1.0 F[/tex]

Plugging these values into the formula and solving for L:

1.1 Hz = 1/2π√(L*1.0 F)2π*1.1 Hz = √(L*1.0 F)6.88 Hz2 = L*1.0 F6.88 H/ F = LL = 6.88 H

[tex]1.1 Hz = 1/2π√(L*1.0 F)2π*1.1 Hz = √(L*1.0 F)6.88 Hz2 = L*1.0 F6.88 H/ F = LL = 6.88 H[/tex]We need to wrap this inductance value with two layers of closely spaced turns around the plastic cylinder.

The inner diameter of the cylinder is equal to the diameter of the wire, which is 0.25 mm or 0.00025 m. Therefore:d = 0.00025 mThe outer diameter of the cylinder is 4.0 cm or 0.04 m. Therefore:D = 0.04 mPlugging these values into the formula for A:

[tex]A = (π/4)(0.04² - 0.00025²)A = 0.001257 m²[/tex]

Plugging these values into the formula for L:

[tex]L = µn²A/lSolving for l:l = µn²A/L[/tex]

Plugging in the given values:

[tex]µ = 4π x 10^-7 H/mn = 2[/tex]

(since we want two layers)

[tex]A = 0.001257 m²L = 6.88 Hl = (4π x 10^-7 H/m)(2²)(0.001257 m²)/(6.88 H)l ≈ 0.0015 m[/tex] or 1.5 mm

Therefore, the length of the inductor should be approximately 1.5 mm.

To know more about oscillator visit :

https://brainly.com/question/31835791

#SPJ11

At t = 5.47 s, the magnitude of the induced emf in the loop is approximately 63.437 volts.

To find the magnitude of the induced electromotive force (emf) in the loop at a specific time, we can use Faraday's law of electromagnetic induction.

According to Faraday's law, the emf induced in a closed loop is equal to the rate of change of magnetic flux through the loop.

The magnetic flux through the loop is given by the formula:

Φ = B⋅A⋅cosθ

Where:

Φ is the magnetic flux,

B is the magnetic field,

A is the area of the loop, and

θ is the angle between the magnetic field and the normal to the loop.

Given:

B(t) = (3.75 T) + (2.75 T/s)t + (-6.05 T/[tex]s^2[/tex])[tex]t^2[/tex] (time-varying magnetic field)

θ = 15.1° (angle between the magnetic field and the vertical)

r = 0.270 m (radius of the loop)

t = 5.47 s (specific time)

First, let's find the magnetic field at the given time t = 5.47 s:

B(5.47) = (3.75 T) + (2.75 T/s)(5.47 s) + (-6.05 T/[tex]s^2[/tex])[tex](5.47 s)^2[/tex]

B(5.47) = 3.75 T + 15.0425 T + (-175.1383 T)

B(5.47) ≈ -156.348 T

Now, let's calculate the magnetic flux at the given time:

Φ = B(t)⋅A⋅cosθ

The area of the loop A is given by the formula: [tex]A = \pi r^2[/tex]

A = π[tex](0.270 m)^2[/tex]

Φ = (-156.348 T)⋅(π[tex](0.270 m)^2[/tex])⋅cos(15.1°)

Φ ≈ -156.348 T⋅0.22946[tex]m^2[/tex]⋅0.96593

Φ ≈ -34.407 Wb (we obtain a negative value for the flux due to the cosine of the angle)

Finally, the magnitude of the induced emf in the loop is given by the rate of change of magnetic flux with respect to time:

emf = -dΦ/dt

To find the derivative, we differentiate the given magnetic field equation with respect to time:

dB(t)/dt = (2.75 T/s) + (-12.1 T/[tex]s^2[/tex])t

emf = -(dΦ/dt) = -(-(dB(t)/dt))

emf = (2.75 T/s) + (-12.1 T/[tex]s^2[/tex])(5.47 s)

emf ≈ 2.75 T/s + (-66.187 T/s)

emf ≈ -63.437 T/s

Therefore, at t = 5.47 s, the magnitude of the induced emf in the loop is approximately 63.437 volts.

To learn more about magnetic field visit:

brainly.com/question/1594227

#SPJ11

The value of the load resistor (R) is approximately 7.47 Ω. The internal resistance of the battery is approximately 2.64 Ω.

To determine the value of the load resistor (R) and the internal resistance of the battery, we can use Ohm's law and the power formula. Let's break down the calculations for each part:

(a) Finding the value of R:

The power (P) delivered to the load resistor can be calculated using the formula P = V²/R, where V is the voltage and R is the resistance. Given that the power delivered is 24.0 W and the voltage is 13.4 V, we can rearrange the formula to solve for R:

R = V²/P = (13.4 V)² / 24.0 W ≈ 7.47 Ω.

(b) Determining the internal resistance of the battery:

The total voltage (V_total) across the battery can be calculated by adding the voltage drop across the load resistor (V_load) to the voltage drop across the internal resistance of the battery (V_internal).

We know that V_total = V_load + V_internal = 13.4 V.

Since V_load = IR (Ohm's law), where I is the current flowing through the circuit, we can substitute I = P/V_load = 24.0 W / 13.4 V.

Substituting these values into the equation, we have 13.4 V = (24.0 W / 13.4 V)R + V_internal.

To solve for V_internal, we rearrange the equation as follows:

V_internal = 13.4 V - (24.0 W / 13.4 V)R.

Substituting the values of V, P, and R, we find:

V_internal ≈ 13.4 V - (24.0 W / 13.4 V)(7.47 Ω) ≈ 2.64 Ω.

Learn more about resistor:

https://brainly.com/question/24858512

#SPJ11

Answer:

The resistor has a resistance of 10.667 ohms.

Explanation:

By Ohm's Law, voltage ([tex]V[/tex]), in volts, is directly proportional to the current ([tex]i[/tex]), in amperes, and by definition of power ([tex]\dot W[/tex]), in watts, we have the following formula:

[tex]\dot W = i^{2}\cdot R[/tex] (1)

Where [tex]R[/tex] is the resistance, in ohms.

If we know that [tex]\dot W = 24\,W[/tex] and [tex]i = 1.5\,A[/tex], then the resistance of the resistor is:

[tex]R = \frac{\dot W}{i^{2}}[/tex]

[tex]R = 10.667\,\Omega[/tex]

The resistor has a resistance of 10.667 ohms.

Ampere's Law is about the relation of the magnetic field and the currents producing it. It is true.

André-Marie Ampère developed Ampere's Law, which connects the magnetic field around a closed loop to the electric currents running through the loop. It asserts that the magnetic field line integral through a closed loop is equal to μ₀ times the total current going through the loop, where μ₀ is the permeability of empty space.

This rule establishes a mathematical link between the magnetic field and the currents that produce it. As a result, the assertion that Ampere's Law is about the relationship between the magnetic field and the currents that produce it is correct.

To know more about Ampere's circuital law, visit,

https://brainly.com/question/17070619

#SPJ4

Answer:

When you go bald

Explanation:

Answer:

Coins made of a good conductor will slow down as they roll past the magnet.

Explanation:

Conduction involves the transfer of electric charge or thermal energy due to the movement of particles. When the conduction relates to electric charge, it is known as electrical conduction while when it relates to thermal energy, it is known as heat conduction.

One of the ways in which a coin operated vending machine checks to make sure that the coins fed to it are genuine is to roll them past a strong magnet. As such, coins made of a good conductor will slow down as they roll past the magnet due to the force of attraction that exists between the magnet and the coin (metal).

This ultimately implies that, the magnet tends to attract the coin to itself and as such slowing down the motion of the coin. Similarly, if it's a fake coin, it simply means it would be a bad conductor and as such it will roll fast past the strong magnet.

In-Circuit 4 of Electricity II, a circuit with a capacitor, resistor, and bulb was analyzed. The capacitor discharges slowly through the resistor in this circuit, causing the bulb to light up.

The capacitor discharges gradually and, as a result, the bulb will light up for a while, but it will not remain lit for the entire time that the capacitor discharges.The capacitor discharges as the bulb illuminates and the brightness of the bulb decreases. After a while, the bulb will go out entirely. The time it takes for the capacitor to discharge and the bulb to go out depends on the capacitance and resistance of the capacitor and the resistor. A higher capacitance or resistance will result in a longer discharge time and a longer time for the bulb to go out. The opposite is also true: a lower capacitance or resistance will result in a shorter discharge time and a shorter time for the bulb to go out.

To know more about capacitor visit:

https://brainly.com/question/31627158

#SPJ11

(a) Yes, it is possible for a large force to produce only a small or zero torque when the line of action of the force does not create a moment arm or when the force is applied directly through the axis of rotation.

(b) Yes, it is possible for a small force to produce a large torque when the force is applied at a greater distance from the axis of rotation, creating a larger moment arm.

Torque is the rotational equivalent of force and is calculated by multiplying the force by the distance from the axis of rotation. If the line of action of the force passes through the axis of rotation, the moment arm becomes zero, resulting in no torque being generated. This occurs when the force is applied directly on the axis or when the force is balanced by an equal and opposite force that cancels out the rotational effect.

Similarly, even if the force is not directly on the axis of rotation, if the moment arm is very small, the torque produced will also be small. The moment arm is the perpendicular distance between the axis of rotation and the line of action of the force. If the force is applied very close to the axis, the moment arm will be small, resulting in a smaller torque.

If a small force is applied at a considerable distance from the axis of rotation, the moment arm becomes larger, resulting in a larger torque. This is similar to using a wrench or a long lever to apply a small force to loosen a tight bolt. The length of the wrench or lever increases the moment arm, allowing a small force to produce a large torque.

To know more about torque here

https://brainly.com/question/31323759

#SPJ4

The image distance from the second lens is approximately 36.4 cm.

What is a lens?

A lens is a transparent optical device that has the ability to refract (bend) and focus light. It consists of a piece of transparent material, such as glass or plastic, that has curved surfaces.

1/f = 1/v - 1/u

Given:

The focal length of each lens (fff) is -16 cm (since it's concave, the focal length is negative).

The lenses are separated by 8.5 cm.

The object distance (u) is 35 cm.

Let's denote the image distance from the first lens as v₁ and the image distance from the second lens as v₂.

From the first lens:

1/f₁ = 1/v₁ - 1/u

Substituting the values:

1/-16 = 1/v₁ - 1/35

Simplifying:

-1/16 = (35 - v₁) / (35v₁)

Cross-multiplying and rearranging:

35v₁ - v₁^2 = -16 * 35

Simplifying further:

v₁^2 - 35v₁ - 560 = 0

We can solve this quadratic equation to find the value of v₁. Using the quadratic formula:

v₁ = (-b ± √(b^2 - 4ac)) / 2a

For the given equation:

a = 1, b = -35, c = -560

v₁ = (-(-35) ± √((-35)^2 - 4 * 1 * -560)) / (2 * 1)

v₁ = (35 ± √(1225 + 2240)) / 2

v₁ = (35 ± √3465) / 2

We take the positive value since v₁ represents a real image. Using a calculator, we find:

v₁ ≈ 44.9 cm (rounded to two significant figures)

Now, we can find the image distance (v₂) from the second lens:

v₂ = v₁ - 8.5 cm

v₂ ≈ 44.9 cm - 8.5 cm

v₂≈ 36.4 cm (rounded to two significant figures)

Therefore, the image distance from the second lens is approximately 36.4 cm.

To learn more about lens,

https://brainly.com/question/28039799

#SPJ4

Answer:

because they are underaged and prob dont care and also the gov thinks that the youth cant make a reasonable decision for them selves for sum like that and the media influnces them to by saying whats going on and who supports who

The q3q3 is located at approximately x = -0.119 m on the x-axis. when the net force on q1q1 is 7.00 N.

Given:

Charge q1 = +3.00 μC at the origin (x = 0 m).

Charge q2 = -5.00 μC at x = 0.200 mm = 0.0002 m.

Charge q3 = -8.00 μC (location unknown).

We need to determine the location of q3 such that the net force on q1 is 7.00 N in the -x direction.

The force between two charges can be calculated using Coulomb's law:

F = k * |q1 * q2| / r^2

Where:

F is the force between the charges.

k is Coulomb's constant, approximately 8.99 × 10^9 N m^2/C^2.

|q1| and |q2| are the magnitudes of the charges.

r is the distance between the charges.

Let's first calculate the force between q1 and q2. Since q1 and q2 have opposite charges, the force will be attractive:

F12 = k * |q1 * q2| / r12^2

Substituting the given values:

F12 = (8.99 × 10^9 N m^2/C^2) * |3.00 × 10^-6 C| * |-5.00 × 10^-6 C| / (0.0002 m)^2

F12 = -0.67425 N

The negative sign indicates that the force is in the -x direction.

Now, let's consider the force between q1 and q3. The net force on q1 is given as 7.00 N in the -x direction. Therefore, the force between q1 and q3 should be:

F13 = -7.00 N - F12

Substituting the values:

-7.00 N = -7.00 N - (-0.67425 N)

-7.00 N = -7.00 N + 0.67425 N

-7.00 N = -6.32575 N

The force between q1 and q3 is approximately -6.32575 N.

We can calculate the distance between q1 and q3 using the formula for force:

F13 = k * |q1 * q3| / r13^2

Substituting the known values:

-6.32575 N = (8.99 × 10^9 N m^2/C^2) * |3.00 × 10^-6 C| * |-8.00 × 10^-6 C| / r13^2

Simplifying the equation:

r13^2 = (8.99 × 10^9 N m^2/C^2) * |3.00 × 10^-6 C| * |-8.00 × 10^-6 C| / -6.32575 N

r13^2 = 0.4048 m^2

Taking the square root of both sides:

r13 = √0.4048 m^2

r13 ≈ 0.6367 m

The distance between q1 and q3 is approximately 0.6367 m.

Since q3 has a negative charge and the net force on q1 is in the -x direction, q3 must be located to the left of q1. Therefore, the position of q3 is approximately x = -0.6367 m.

The q3q3 is located at approximately x = -0.119 m when the net force on q1q1 is 7.00 N.

To learn more about force, visit    

https://brainly.com/question/28572157

#SPJ11

Explanation:

Cultural Ecosystem Services (CES) are the non-material benefits people obtain from nature. They include recreation, aesthetic enjoyment, physical and mental health benefits and spiritual experiences. They contribute to a sense of place, foster social cohesion and are essential for human health and well-being.